After turned down two time by Airtel, for new broadband connection. I opted for tikona, without wireless router. As, I had beetel ADSL2 + wifi router with me, from my last airtel connection. I thought of using it. It turned out to be real easy thing to do. Only 4 steps and wifi setup was done.
1. See the under of the router, you will find a reset mark, just insert and press button, to reset your router to default factory settings.
-or-
1. Open 192.168.1.1 (link to acess, settings page of router), and from there also you can restore to factory settings. I prefer first option as it was fast.
2. After resetting the router to factory settings, open the link 192.168.1.1 to configure it.
3. Click on “Interface Setup -> Internet -> Encapsulation -> ISP -> Bridge Mode.”
4. Now to configure for wifi acess, select “Interface Setup -> LAN -> DHCP -> Disabled”. Or else you can use, router through LAN (Didn’t tested it for more then one system in LAN, as I had only one lappy).
5. Next step is to configure router to be secure, password setting, mac association etc. Read this comment by Rajat Gupta, it tells you more about mac address and it’s coloning, Thank you Rajat for it! ๐ Never thought that, tikona can use MAC to keep system count.. ๐
6. Final and important step is to restart the router for changes to take place.
Hope, it was quite helpful to you all. And i think, you will be able to use these steps to configure your ADSL wifi router with any ISp
.
Nitin Kumar's Blog 
Hi Buddy,
I tried this however unable to connect. can you help ? I am fed up with this and there is no one from Tikona to help me. I would appreciate your help if you can guide me on this post or by calling +91-9999975277. Else send me your mobile on my email – gupta.kosh@gmail.com.
Thanks
where r u from , i have setup recently but you should have your login password.Have you setup the modem yes or not. If needed i will send you full setup copy by mail so that by making little changes in configration in your area it will help you to start
hiii hello , i have a beetel 450tc2 router , i dono how to connect to my beam connection, can u help me ?????
dude i also have a same modem with me but the problem is with port as beetel router works on small port and the modem with tikona has big port any solution dude
@Abhishek.. My airtel modem is (450TC1 ADSL2+Router), what I did is.. from tikona machine.. I connected the lan out into one of the lan ports in the modem. And that worked for me.. And my lappy to other lan port on my modem.
@Kaushal … sorry for late reply man!! I didn’t noticed your comment before. You still facing the problem?? if yes, then we can try to find out the solution.
can you show me the image of the router cable connected to the modem..??our cable have 8teeth /cable points in one pin…
I have added the images, what I have done…
From tikona adapter, LAN port Connected LAN port on my airtel wireless modem.
ive seen the images thank you……can you tell me the details of configuring this modem. We have been connecting these pins/ports,but the internet signal in the modem has not been flash,and cannot browsed….??we do not know how to configure….
internet signal in the modem won’t flash, coz, it’s ADSL modem, and cheks for DSL signla.. which is not present.. that’s why we are just converting it to a router… only as connection between tikona and system.
we have connected bt it requires username and password……..??
yes, I think, if you have done reset for the modem, then the username will be admin and password will be password. Try it, hope it works.
I also face the same problem after resetting my modem it ask for id and password… i have tried id as ‘admin’ and password as ‘ password’ but it does work can you help???
no idea Tushar, admin/password is only default that I know.
can u please help me ut with the wireless part and how to configure the mac add etc…
For wireless MAC address filter : enter the mac addresses of the devices you want to connect through wifi, to know mac address.
1. In windows on the command prompt enter command : ipconfig /all
this will give output something like this :
Wireless LAN adapter Wireless Network Connection:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Atheros AR9485WB-EG Wireless Network Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Enter the physical address without ‘-‘ in the MAC Address in the way it is mentioned.
2. For Linux, you can run command : ifconfig, to get MAC or Physical Address.
3. For phones, look for mac address in wifi settings.
Good to know this…. I will try it today for my ADSL router and will let you know.
@enitinkumar: Hi Dude..Thanks a lot for the above suggestions to How to configure the Beetel ADSL2+Router for Tikona…We tried the whole day from our own but got failure..Just googling about the steps and found ur blog..it really workred for me..Specially the snapshots you have attached, it was so useful..Thanks a ton mannn:)
Welcome Amit.. ๐ ๐
Hi Nitin, I have Beam connection and Beetel 450 TC1 . Please tell what should I do so that I can use the same beetel device as router only?
Hi Rahul, what ever I have configured is on the side of wireless router only (Beetel 450 TC1), so you can try the step and, then try connecting it to your Beam connection. Best of Luck!!
Hi I did following but no success
1. See the under of the router, you will find a reset mark, just insert and press button, to reset your router to default factory settings.
2. After resetting the router to factory settings, open the link 192.168.1.1 to configure it.
3. Click on โInterface Setup -> Internet -> Encapsulation -> ISP -> Bridge Mode.โ
4. Now to configure for wifi acess, select โInterface Setup -> LAN -> DHCP -> Disabledโ.
5. For wireless MAC address filter : I enter the mac addresses of the devices
But same result “No Internet Access”… Can you please help me ?
Hi, if you are able to connect to the wifi router after following the above mentioned steps, then you have followed the correct steps. And configured it right. And that’s what was my aim while configuring beetel router, just to provide wireless connection to my devices, for connecting to internet from tikona side, nothing changed for me..
Now, if beam has some issues with it, like it doesn’t recognizes any other devices, other then you registered pc mac id, or something. I don’t have much
Hi, if you are able to connect to the wifi router after following the above mentioned steps, then you have followed the correct steps. And configured it right. And that’s what was my aim while configuring beetel router, just to provide wireless connection to my devices, for connecting to internet from tikona side, nothing changed for me..
Now, if beam has some issues with it, like it doesn’t recognizes any other devices, other then you registered pc mac id, or something. I don’t have much idea how beam interface is while connecting to internet.
Hi Nithin,
How to configure the Beetle 450TC1 ADSL2+Router for both desktop and laptop at a time. i followed your steps and configured,But it is working for either desktop or laptop at a time.could you please help me to connect both desktop and laptop at a time.
Hi Kishore,
Can you elaborate your problem more?
because, with my tikona service I am allowed to access internet from two system at a time, after logging in through tikona portal. But, there is no limit to connection to the wifi router, I have connected my phone, 2 laptops, ps3(both wifi or via lan) all at the same time, with the present configurations.
So, please check if the problem is with the service provider that it allows only 1 system to be connected to internet.
HI
Noble deed you are doing Dude.. Big respect… I could not utlize my 450TC1 ADSL2+ Router for a long time since I got a new Tikona number. after following the steps you said connecting via lan cable after resetting the router I opened the link at http://192.168.1.1/ it asks for username and password.. I dont know how to get past this I tried Admin Admin, Admin Password User Pass combo .. to no avail… Please Help me ….
Hi Arthaf,
Thanks for your nice words.. ๐ I just shared my experience, and it’s great to see it’s kind of useful to many!
try username : “admin” and password : “password” , after resetting this is the password for me!
Password worked like a breeze… after I pressed the reset button for 15 secs….. then followed all the steps you mentioned…. But now it asks for a network security key . I have no clue what it is..
arthaf, I think it’s asking for network security key when you are trying to connect to the wifi network, then it’s asking for the WEP Key#1 mentioned like this in the https://enitinkumar.files.wordpress.com/2012/02/wireless.png pic.. check what you have entered there.. and if you want to change it.. you need to disconnect from tikona.. restart your router and then again login to it using lan cable and open 192.168.1.1 again and configure that password. Hope this helps you!
๐ฆ now am not able to connect the router via lan and connect to 192.168.1.1… the browser does not show anything. not able to connect. . . . Help
try removing tikona lan cable from the router, then again restart the router, this time it won’t take ip address from tikona, and you will be able to access 192.168.1.1.. ๐ and if this too doesn’t work, just start from beginning.. means.. from resetting your router!
Dear Nitin,
My WIFI is ON !!!!!!!!!!!!!!!!!!!!!!!! Unbelievable…. ๐ ๐ ๐ ๐ ๐ ๐ ๐
Cant thank you enough for having helped me out. Had almost dumped the router which I was so used to due to the connection change after the tikona and airtel guys dint bother to help.
Like you said I restarted the process just like you had advised. Every step you described was crystal clear and worked so well. You are a true savior.
Thank God for having sent people like you to us mortals.
Whenever you are in Delhi please email me arthaf@gmail.com. . .The treat is on me ๐ .. do mail
and I am sharing your blog on FB.. with you r permission
Thank You Again ๐
Have a blessed life
Thanks Arthaf for your encouraging words! ๐ I never thought my experience sharing will be so much useful to you all.. And thanks for the invitation, whenever I ll come to delhi, will surely try to meet you. Not, just for the treat.. ๐ And no problem with me, whatever I write is open to all, you can use, share. I usually remain online on skype “enitink”
And my best wishes to you too, have a great blessed life.. ๐
Thanks.
Had a old Airtel wifi router which turned obsolete once I moved to delhi and had got a Tikona connection. or atleast I thought so.. Thanks to Mr.Nitin and his blog.. who guided me step by step and helped me get wireless on the same router… Thank you Nitin Kumar … thanks a wireless Tonne ๐ โ
http://www.facebook.com/arthaf.mk
Hey Nitin,
I have got another connection(spectranet) not Tikona, but again is through LAN. Here I got a static IP, subnet mask,gateway and a DNS server. Could you tell me where exactly should I put those values, while configuring the router, so that I can use my beetle adsl router to good use?
Hi,
Can you let me know ;
1. What steps you have tried??
2. And after entering values of static IP, subnet mask etc, do you still need to sign in?
Hi NItin,
I tried giving IP, subnet mask, dhcp(i gave it same as dns) and dns in the LAN section.
Still no change.
I tried your way of disabling dhcp also with no benefit.
I tried putting the values of IP etc. in “internet” tab. that too did not work.
My connection when connected directly to the comp via lan port needs me to change the ip, gateway, subnet masks of lan adapter and further I need to login to spectranet page which will be auto directed when i type any link in browser.
While changing the router IPs, I am not able to get that login prompt in browser, but it just says no internet
Hi ,
I think disabling dhcp and bridge mode, should have worked in your case too. But, if it didn’t then sorry man, I don’t know what else to do, that can work!
Other things like configuring it with static IP address won’t work, as it requires you to sign in from portal. I don’t remember properly, but I think with the case of airtel we used to save airtel’s username and password to automatically sign in, may be you can try it the airtel way, reset your router and send static IP, and username password there.
Just try once more disabling dhcp + bridge mode + configure your system with static IP etc values given to you. But I feel it won’t be of much help as at a time only one system can have that IP. No multiple systems won’t be supported.
Dear Nitin,
Thanks a lot for the information above. After following the steps , i am able to use tikona connection through wi fi and LAN but there is one problem, every device which i use to connect through my modem ask for login information of tikona and i can’t use internet on more than two devices at a time. One thing more does mac filtering ( under WAN) help in anyway except protection ? Can you please help ????
Hi Rajat,
That’s the problem with tikona, I too have to sign in from every system, and max two is supported so have to logout from one to connect to some other.. ๐ฆ
Yes, you are right MAC filtering is only for protection, nothing else.
Thanks a lot Nitin !!!
But i have a good news…you can connect more than two device using tikona and TC450. GO to your network connection in Control Panel.
Now right click the LAN or WAN connection through which you are connected.
Now go to Properties> configure > Advanced > Network Address ( it may be by a different name in some cases) .
Enter the same MAC address (12 digits- B8-xx-xx-xx-xx-EC) in all your devises like this. N you are all set !!!!
Log in from as many Laptops or Desktops as you like just change your MAC address like this.
Note : you can get the MAC add of your device by going to command prompt and enter the command :
ipconfig/all
or
getmac
Enjoy Everyone !!!!!
By the way this is called MAC cloning.
Thank you Rajat, never thought tikona might be using mac address!! will try it.. ๐
my pleasure mate !!
Hi Rajat,
I really appreciate ur effort and i guess,i am having the same trouble so need ur help.
As u know that tikona is using MAC address for filtering and with my plan at max 3 device can login simultaneously .
i was already using 3 laptops but need to connect the 4th one also. so i tried to use MAC cloning of the 4th one with one of the laptop. cloning was successful but not able to access the net on both the systems simultaneously.
1. both systems are taking the same ip after cloning
2. both systems are taking different dhcp server address.
when i connect with cloned system,proving the mother system not connect,net is accessible.
but when i connect mother system,cloned system starts reacting otherwise means net is
unaccessible.
Awaiting ur kind response.
##thanx in advance.
You can statically assigned IP to your systems. Since you have upper limit of 3 Mac address, use 2 as normal and clone one for all desktops which are supposed to be connected with same network.
Hi Rajat,
I am stuck with MAC cloning part. I have already mapped 2 pcs and 1 laptop mapped to Tikona. Now I configured router and trying to access the same laptop from wifi but it is giving me mac connections not more allowed.
Can you please help me here in mac cloning. I tried giving my laptop mac ip to the WAN connection network address but still getting the same issue.
Kindly help me in MAC cloning part.
Thanks in advance,
Manoj Kumar
i am also going to buy tikona connection and i have beetel 450tc1 router…..
how is the service and speed of tikona….
tikona service depends area wise! it’s ok kind! not too good not bad!
iam having a 450tc1 router with me. i have done the reset on the router by clicking the reset button. but when i am opening the http://192.168.1.1 it is asking username and password. i tried with admin and password but its not opening. can you plsssssssss help ?
default username and password for the router is admin and password respectively, I don’t think it’s something different!
did u reset the modem correctly. u hv to hold the reset button for 10-15 sec.
use username: admin & password: admin or 1234
Hi tried with the user name and password provided by you and still it did not worked. and promped me with and error message as below.
” Protected Object
This object on the RomPager server is protected ”
Please let me know how can I login and get started with my Wifi connection. I am very upset after getting this modem.
Hello Nithin,
I am trying to configure a Beetel 450 bx1 router, but could not find the hard reset pin any where. Is it possible to post a photo of the same from Beetel 450 Bx1, if you could.
Thank you!
Guruprasad
Hi Guruprasad,
hope this image is of some help to you!
Hi Nitin
i have the same router Beetel 450 TC1-ADSL2. i want to make wifi connection with TIKONA ISP.
initially i tried my own methods but failed then i saw your blog and start following your steps but not able to connect.i tried your steps 4-5 times from beginning.
tikona customer care and beetel care both are not assisting me on this.
i am using Dell-Latitude model laptop with windows-Xp service pack-2.
can you please help.??
After seeing above comments,my only hope is you.
## humble request.
Thanks in advance
Hi Ankur,
surely would try to help you. can you tell me, where are you exactly failing in getting it done?
After following all your steps,i put in the tikona lan cable in lan-1 port(actually tried all the ports) . after all this i am able to connect to wifi with system getting the IP address.
but not able to browse internet.
i tried to open 1.254.254.254(tikona’s user home page to login) but not getting results but i am able to open 192.168.1.1 when connected to wifi.
After following the steps, you won’t be able to open 192.168.1.1. And system will get IP in series 1.x.x.x. Then only you will be able to login into tikona’s user home page. After configuring the router, don’t forget to restart it.
I tried this 10-12 times already but getting the IP address like 192.168.1.2
any other method to set the desired ip and able to open tikona home page?
Hey Thanx a ton buddy..!!
u r a true savior. i got the issue because of not restating the router after configuring.
now it ON ๐
God bless u dear..!! ๐ ๐
welcome Ankur!! ๐
Hi Nitin,
thanx again for ur previous help on connecting with router but this time i am having some other issue.
as u already know that tikona is using MAC address for filtering and with my plan at max 3 device can login simultaneously .
i was already using 3 laptops but need to connect the 4th one also. so i tried to use MAC cloning of the 4th one with one of the laptop. cloning was successful but not able to access the net on both the systems simultaneously.
1. both systems are taking the same ip after cloning
2. both systems are taking different dhcp server address.
when i connect with cloned system,proving the mother system not connect,net is accessible.
but when i connect mother system,cloned system starts reacting otherwise means net is
unaccessible.
Awaiting ur kind response.
##thanx in advance.
Hi Ankur,
Sorry, I coudn’t try mac cloning, cause win 7 was not allowing it… ๐ฆ so no idea what to do in this case, may be Rajat Gupta will be able to help you, ask him, comment on his post.
hi..can you tell me how to connect tikona wifi to xbox live???…i am using my personal beetle ADSL2 +router(wifi)…
Hi.. I tried with my PS3, went to settings and internet, and configured wifi connection. Then using browser, I logged into tikona service. Not, much of idea about xbox interface.
Hi Nitin
I am having the same router Beetel 450-TC1 ADSL-2 and i want to use it as wi-fi with TIKONA service But i am not able to connect it according to your step(Provided above).i have tried this method a lot times.
i m using Dell-Latitude laptop with windows-xp sp2.
Please help me with this.
##Humble Request.
where do you get stuck ?
Hi Nitin
I am getting a Page saying Device error while connecting. I even restarted the router while connecting.
Regards,
VIjay Raghav
Hi Vijay,
After following all the steps you are getting this error?
Hello Nitin.
I am able to configure and get Tikona IP from Router, however I am not getting Ping response or for that matter open any website’s. Not even Tikona’s login page. I am running on windows 7
Hi Nisarg,
Try connecting directly through the tikona lan wire, see the IP series, and check while connecting through wan too you get the same IP, if it’s so, then there should not be any problem while getting tikona login page. I use, windows 7, so didn’t configured it specially for tikona~!
Hi Nitin,
I have Airtel LAN connection and I wanted to make it wifi. I called Airtel and they said they dont provide wifi routers. So I bought Buffalo Airtstation router. Now I have Airtel modem and router. Now Airtel guys say that they cant configure Buffalo router. Please help I dont know how to configure this router.
Hi Randheer,
Just connect the wifi router to the Lan port of the airtel modem. I don’t think you need to do anything extra!
Airtel guys provide wifi routers too, but don’t go for it, as you will have to configure them again for any other ISP.
bro cant configure it. It seems like I have to buy a new Beetel router and throw this Buffalo router.
sorry man!! couldn’t help you out..
dear nitin kumar thanks ๐
most welcome sir!! ๐
I was able to proceed till disabling DHCP after that what we have to do to set MAC address. Because I am setting my laps WLAN Mac I’d there and it’s conn but not able to get tikona login page could someone pls help
Setting MAC address is not so important, if you want to keep your wifi more secure then only go for it, else not needed.
Compare the IP addresses, in case when you directly connect the lan wire from tikona modem to your lappy, and when you connect through wifi. They should belong to same ip group. if that’s not the case, try again all the steps, and don’t forget to restart your wifi router.
thank you so much nithin i got the wifi on my laptop, I checked the IP on the LAN connection which was in the format 10.192.xx.x, and when trying with wifi is like 192.168.xx.xx, so i went inside the router page and after that i chaged router ip from 192.168.xx.xx to 10.192.xx.xx, after i am able to login and use wifi on my latop. but i am not able to do the same on my iphone and the other lap its giving the tikona log in page on the both but its telling on both authentication failed as number of maximum allowed of session reached… and also i am not able to access the beetle page using 192.168 nor 10.192. and what should be done in this case. if you could help me i would really be greatfull.
Thank you once again for helping me to set up wifi atleast in one laptop
Hi Arun,
Just confirm once, if tikona has given you access for one system or what? if it’s so, then you will have to try MAC cloning, though it didn’t worked for me, but you still can try.
Other than that, I didn’t configured my router with any IP, I just selected dynamic IP, try it! not sure, but configuring IP from your side might be the problem.
Hi Could you please help me in configuring iBall WRC300N router with Tikona.
Hi, I searched for iBall WRC300N, and got this user manual, http://www.iballbaton.com/Download/125/Manual.pdf , go to the page no 13, – it shows selecting from ‘Ethernet WAN’/’ADSL WAN’. Ethernet WAN and from the next page options, Dynamic IP combination should be what you are looking for. Hope it works, try! and let us know, if it works ๐
I have configured with the above procedure and successfully connected to internet.But now i want to configure for all my 3 laptops and tablet.Can u tell me about the configuration
And when i enter more than one mac address in mac association.i can redirected to 192.168.1.1
sorry, am not able to understand your second question…
“And when i enter more than one mac address in mac association.i can redirected to 192.168.1.1”
Just connect to the wifi, and from each of your laptop or table, you need to login to tikona! but, you will be able to connect, as many tikona allows, like for me tikona allows upto two connections.
Hey Nitin…..
Today in afternoon i just ordered for Netgear router coz Tikona engineer said that the MTNL 450 TC1 router canโt be used as a WIFI router and will have to purchase a new WIFI router.
I tried once from my end but failed then after a long time today I finally searched for best WIFI router and placed the order on Flipkart.com, still somewhere I was unsatisfied…. it was just where I googled and found your blog.
I read your whole blog but unfortunately couldnโt try it out as I was in office and even didnโt cancelled the order from flipkart.com as I was little sceptical. Just now I came home and did step by step the way you have explained… I must say you are truly genius and like Amitabh says in kaun banega corepati “Gyaan Hi Appka Haq Dilaati Hai” which u had shown by proving all worn whoever said that 450TC1 WIFI+ADSL Router couldnโt be used in Tikona Broadband.
Hatโs off buddy….. and appreciate your knowledge and moreover your kindness by sharing your knowledge with us.
Thank You Once Again ๏
Manohar Poojari
Thank you for your kind and encouraging words Manohar. ๐ It feels really great my simple blog has been a great help to you all.. cheers!! ๐
Hi Nitin,
Nice job by the way. its hard to find hack support on indian devices.
i have the same prob as Arun.
“”ARUN says:
January 8, 2013 at 2:34 pm
thank you so much nithin i got the wifi on my laptop, I checked the IP on the LAN connection which was in the format 10.192.xx.x, “”
not able to connet the phone to wifi. tried cloning the mac. no luck.
also i am not able to connect to the adsl 2 page. 192.168.1.1.
checked the default gateway. gave a 10. series ip.
i have connected the 450tc1 to another router (belkin). both routers are allowing access to the net.
but not able to connect anything apart from 1 laptop.
please advice.
Sorry Arun,
I have posted, the problem I faced, and it’s resolution!! But, I didn’t faced the issue in connecting multiple devices. to my router, I can connect as many as I want. But, tikona has given me internet access for just two devices, so, other devices are just connected to wifi network!
Didn’t faced, problem that you are mentioning, am also not very clear what went wrong at your end. So sorry! no idea on how to resolve it!
looks like we have to clone the router mac to match the system. and enable the dhcp in the router and then we can connect multiple device.
sir pls help i cannt get into the configuration for the givn ip address 192.168.1.1.. pls help…
Hi Abhay,
what is the issue that you are facing? not able to access 192.168.1.1 ?? if it’s like then, then try resetting your modem, you need to press the button till all the lights on the modem don’t go off!
Then, connect to the modem through lan/wifi you will will be able to access 192.168.1.1. And don’t forget to remove all other lan wires, except the one connected to the system through which you are trying to configure it.
it is showing that firefox cannt find server. when i connect the net via 3g dongle and then try to access the ip it prompt for username and password. and when i entered admin and password it promts again… pls sir help me out….
I am not sure, by 3g dongle, which IP you are trying to access.. ๐ฎ
you need to access 192.168.1.1 for your router, and 3g dongle won’t be able to connect to it.. reset will work, once you reset, you will get 192.168.1.1 page. Try properly resetting your router.
can we use th beetel router after all settings done to use wifi on mobile
yepp, it works for me.. ๐ bt, keep in mind, tikona has something device associated list too, first it allows you to connect through limited number of devices to internet at a time, like for me it’s just 2. Secondly, if you have tried to access internet through multiple devices, after some time it tells max limit reached for associated devices.
Hi Nitin,
I read your blog, also used one of your pictures to post at India BB forum:
Beam Broadband – Howto PC plus Laptop:
http://www.indiabroadband.net/cable-internet-services/44591-beam-broadband-howto-pc-plus-laptop.html
Could you throw your inputs on the approach? Is it correct? How about Network settings?
Thanks a lot
tikona conxn connected to belkin router works like magic. i have the airtel modem. 450tc1 which is connected via rj45 and entends the wifi.
but i want to connect the 450tc1 to the belkiin router wirelessly.
is it possible. any suggestion. ?
i have beetel 450bxi, the interface u provided in pic is diff in 450bxi, can u guide me in doing the changes in beetel 450bxi.
can you share, the pics of the interfaces!!
the main interface is
http://screenshots.portforward.com/Beetel/450BX1/
interface is really different !! ๐ฎ please give me some time, need to see all the pics!!
Dear i have doen your prescribed settings but the connection is again and again disconnecting and reconnecting.
Please Help ASAP
Dear i have doen your prescribed settings but the connection is again and again disconnecting and reconnecting.
Please Help ASAP.
No, idea about it Sunny! I some time too face this issue, internet goes for some time and automatically it comes back, through out the time am remaining connected to the wifi, it’s something to do with tikona only!
Hello NItin,
Good to see that your post helped people a lot !!
I am also planning to take Tikona. What I do not understand is the fact that Tikona already provides us with a wireless connectivity which helps us to connect our devices (wireless-ly)
So what is the use of configuring the Beetel 450TC1 to give wifi connectivity, when wireless connectivity is already provided by Tikona ?
What I understand from your post is that you are using a Ethernet [LAN] cable, to connect Tikona’s modem’s Ethernet Port (as you have shown in figure) and to the Beetel’s Ethernet Port. This way you are getting the Internet connection on your Beetel Modem, which can then be used by other devices connecting to your Beetel Modem. Is this correct ?
If yes, then I would say that this way you are just extending Tikona’s wireless connectivity.
What I want is that, I don’t want to use Tikona’s Modem, as I have a Beetel Modem with me. So, I don’t want to purchase their modem, thus saving installation cost. Now, what is the way to configure my modem ?
Remember, Tikona is not giving modem since I am not asking for it. So your diagram of LAN to LAN connection will not work.
I would be really helpful if you can guide me on this.
Hello Arunav,
Tikona gives both type of modem wireless and lan based, mine is lan based. And for wireless modem they ask for around 1.7k extra. But, from my previous connection I had beetel ADSL modem, so I wanted to use it, and succeeded in doing, so I shared my experience how I did that here.
Am not extending tikona’s wireless connectivity, I just made my wired lan to wifi lan.. and this wireless lan is connected to tikona’s lan. Hope I made my point clear ๐
There will be a base installation cost, that you can’t avoid, only using your beetel modem you can save what they charge extra for their wifi modem which is not default package part. In the base installation, they will put a wireless receiver on the roof, and connect it to an adapter cum modem inside your home. Now, in the pic the modem you see which is connected to beetel modem, is the adapter that does both supplying power to the wireless receiver on the roof and also giving a lan based connection.
The LAN to LAN connection will surely work, as they will give you a LAN connection to connect to your system, if they don’t then think how you will be able to access internet in your system. If you have planned to get tikona, then let them do there part, once their configurations are up. Then try the above mentioned step to get a wifi connectivity… ๐
Oh… that was indeed an information for me. I was not aware that Wifi is not the default installation option for Tikona.
Thanks NItin.. and thanks for quick reply too… !!
I too have same modem as yours and will use the steps you mentioned to enable Wifi ๐
Thanks !!
most welcome ๐
Anyone tried/trying the same device with Beam?
PC connects to Internet via Router (Bridge + DHCP disabled) as switch. IP config:
Dhcp Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
IP Address. . . . . . . . . . . . : 183.82.xxx.xxx
Subnet Mask . . . . . . . . . . . : 255.255.192.0
Default Gateway . . . . . . . . . : 183.x.xxx.x
DHCP Server . . . . . . . . . . . : 183.x.xxx.x
DNS Servers . . . . . . . . . . . : 123.xxx.xx.xx
123.xxx.xx.xx
Whereas on Laptop, I’m able to see and connect to Wireless SSID. But when I open any website, it says:
“ADSL Modem link is down!”
Laptop, IPconfig I see in this fashion:
IP Address. . . . . . . . . . . . : 192.168.1.3
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DHCP Server . . . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 192.168.1.1
192.168.1.1
Is this because laptop can’t get DNS Servers? I don’t get what’s happening. I could only access the Internet from Laptop just for once. Next day, it’s gone. I could only connect to the SSID but no Internet!
IMO, this device acting strange with Beam network.
Hi,
The method which Nitin has given to us is generic and not bound for Tikona. This is what I believe. He has given us a way to make your Internet connection, which is wired over LAN, go Wireless [WiFi] by using the Wifi Modem of your choice.
So, if Beam provides you with the Lan wire, just connect your Beam’s LAN wire to your own Wifi Modem’s Ethernet port and follow the steps NItin provided.. They are really helpful.
And don’t forget to share the feedback.. ๐
Thanks
Arunav
I tried a lot since last week:
#Beam fiber cable goes into Router’s LAN1 port (RJ-45)
#From Router’s LAN2 port, Ethernet cable goes into PC (RJ-45)
I tried a lot of settings. Only once I could able to access the internet on Laptop, also on PC. Of course, Beam doesn’t web authentication allow multiple logins – yet to test Mac address solution to over come this. What’s puzzling is Laptop connects to the SSID but no internet!
Internet on PC works (bridge mode) fine but this isn’t not the priority. I’m looking to find a way to provide internet on my Moms laptop through my PC beam connection. So I need this Router to do the job. Previously with the same Router, we used to connect on multiple machines using Airtel broadband.
Do I need to enable any service on Windows XP? I’m not really sure.
Hi and thanks nitin kumar,it all worked like charm but i am only able to connect 2 devices at a time and not more than that. A solution would be appreciated.(Tikona engineer came to my house to fix my line, he said port forwarding might help but i did not get that ,of course he did not do it for me)
Hi Ankit,
Sorry, I haven’t tried connecting more then 2 devices. and also I don’t have idea about port forwarding. I ll try sometime and if I find solution then would share here. If you come to find any solution, do share with us.
Hi Nitin,
I have a question for you.
I am using Tata Photon+ with a TPLINK 3G/4G Wireless N Router TL-MR3220.
I have a spare Binatone 4 Port ADSL2+ Router with Wi-Fi(DT850W โ 150Mbps).
The TPLINK WIFI-router is attached on 1st floor of my house and on the ground floor
I am not getting good wifi signal. I am thinking of using the Binatone Router to
extend the wifi to ground floor. The Binatone Router does not have a WAN port.
Can we connect TPLINK and Binatone routers through a LAN cable and setup
Binatone router to take input from TPLINK throuch LAN and act as a wifi
router for ground floor?
Is this possible? If so, what settings should be done.
Thanks,
Gaurav
Hi Gaurav,
as I feel, you just want to use your Binatone ADSL2 router as a bridge. So, you can try the settings that I have done. Interface would be different. But, you should be just looking to configure your Binatone router in bridge mode, and also dhcp disabled.
Earlyer I was using the BSNL broadband mordem ADSL-2 for the internet.
( input type : RJ45 connector
Out put : Ethernet port connetced to my computer)
Wifi : Available )
Now I am using the cable internet service
(Input : coaxial cable
output : Ethernet port connetced to my computer
Wifi : Not Available )
Problem : As the cuurent cable connection internet modem dont have the wi-fi , I am unable to connect my samsung moble phone.
Help required:Kindly guide how to make my BSNL broadband mordem ADSL-2 as a router
just try enabling bridge mode for you router, and also disable dhcp for the router.
Tried the steps. Worked like a charm. Thanks mate, god bless.
Hi I am trying to go to the Ip to setup the pasword. but it is not taking the default user name and pass as (admin/admin). Is there some other password also. I need to setup this modem with MTNL connection.
Im getting this peculiar msg and i couldn’t get the login page with above settings. Pls reply
Im getting this peculiar msg and i couldnโt get the login page with above settings. Pls reply
this should not come, as we have enabled bridge mode.. just retry the steps, and don’t forget to restart the router after the settings are done.
Have done it. FYI..im not a noob here. Tried success with DLink 2750U already. Pls help
HI Nitin
i had been trying to configure my ADSL router for long time, but never get succeed.
i went through your blog and configured my router as you have mentioned. but always got
“Your ADSL router not configured properly” error
one day i waited for few minute and then tried……Amazinggggggggggggg its workinggggg
ji would like to say that to all users you might get this error…just wait for few minutes and see the MAGICCCCC
This Wireless Router is quite weird, wasted a lot of time over time. Nevertheless, it’s a done deal now. My problem solved. Beam service is available on PC and Laptop, yet to test simultaneous connections.
How to allow certain ip for all services in beeteel routers?
Don’t think there is any option for IP address related filtering! ๐ฆ
Hi Nitin
I have a D-link ADSL2+ router. Could you pls advice how to configure it for Tikona.
Hello Balyan,
Just try to set it up in bridge mode, and disabling dhcp. Step 3 & 4 are important. Try to find interface to set it up for you router.
Tried to reset the modem but still no go on my air tel modem.could you please tell us the procedure to connect it.if I reset my modem will it shows the wireless device as admin?
Resetting works, try for some time, it’s not very important to reset. It’s just good to reset to factory setting before trying your own settings.
your second question “will it shows the wireless device as admin?”, sorry, bt am not able to get, what you are asking about!
by nitish———need help!! I USED to bsnl broadband.but i switch to tikona internet.please tell me can i use my iball adsl2 router with tikona?? also tell me can i use 3-4 pc with 1 tikona ID.
Just try to set your modem up in bridge mode, and disabling dhcp. Step 3 & 4 are important. Try to find interface to set it up for you router.
Regarding connecting more pc from tikona, you will have to try mac address cloning, though it didn’t worked for me. So, am also not able to connect more then 2 devices at a time.. ๐ฆ
Thanks man!!!! ๐ ๐
Hey, So what I’m trying to do is:
Have a Digisol router which takes a LAN cable as input for the internet and then creates WiFi. I’m trying to extend the range of wifi , and trying to connect a Beetel ADSL2 router to it, (through cable or any other way possible) so that the second (Beetel) router acts as a repeater of sorts.
Completely failing to do this, could you please help?
Thanks.
Abhishek.
plz somebody help me with dlink 2750u configuration for tikona
Hi thanks to your blog, reusing my existing tp link adsl wifi router was such a breeze! Keep up the good work..
Hi Nitin, Thanks a lot for your help. I was finally successful in configuring my Beetel 405TC1 router with the tikona broadband. but i would like to add some steps there if some one is unable to connect to the internet after following above steps, I would recommend the below settings as they helped me to connect easily.
1. Select Dynamic IP address in the screen Interface setup>Internet
2. Disable DHCP in the screen Interface setup>LAN
Can you help me i have “450tc2 wifi modem” .
Please tell me how to remove default wifi SSid Index named as “MGMNT”…
please tell me how to remove from admin panel
hi.. i have a linksys wifi router with LAN port as internet input option. i have got BSNL broadband connection where the pin is smaller in size. how could i use this modem without buying a new one
hi, you need to get a adsl modem, BSNL broadband connection will go into that, and from adsl modem take the lan cable to your linksys wifi router!!
hi, i just got airtel broadband with a wireless router need some help to connect my sony bravia tv through wifi….i tried but its asking to enter some pin number to the router using pc, i couldnt find where to enter the pin number….pls help out
hi, extremely sorry to say! I really don’t have idea about what you have asked.
hi..im having a problem with my Beetel 450tc1 adsl2 modem…my wifi connection have been used by my neighbours too..so i was trying to change my password, but the server cant accept my password and username…i have changed my password once…please help me….
hi.. you can reset your beetel modem, then it will take default username/password, which is admin/password. but, if you have your ISPs username password then only do that..
Nitin.. Help me too plzzz
I resest my modem thrice till now and every time i connect lan cable i am getting status as undientified network.
Not able to open 192.168.1.1 and nothing is happening
Hi Varun,
confirm after connecting the modem through lan cable, if you are getting ip address like 192.168.x.x or not? if not, then check your ethernet port’s ip setting if it’s configured as static!
Dear Subscriber,
Please be assured that your concern listed July 12, 2013 has been noted and our team is working on addressing the same.
Regards,
Tikona Care
Dear Subscriber,
In order to assist you further, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKJL796 to your case. Requesting you to mention the reference number in the subject line while sharing your details with us on tikonacare@tikona.in.
Regards,
Tikona Care
Hi Nitin, I don’t know much about computers. I also have 450TC2 beetel router. I followed your instructions to configure the router. Can you please tell me the steps to then set up the wifi connection and use it in two laptops(I don’t see any wifi being set up). After typing the MAC Address of 2nd laptop in the router config. what more steps need to be followed to start using wifi.
Hi Arjit, MAC addresses are for extra security if you really need them! if not, then you can skip them.. ๐
Dear Arjit,
In order to assist you further, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKJL1863 to your case. Requesting you to mention the reference number in the subject line while sharing your details with us on tikonacare@tikona.in.
Regards,
Tikona Care
I was buy Beetel 450TC2, DSL and Internet Led All ready flashing and working properly but i can’t enable browing Internet in desktop or laptop, i was also fixed DNS but not sucess to browing, i have BSNL Internet, please help me for that issue
Sorry, not much idea about BSNL related configurations!
Fantastic post !! i was able to successfully reuse my beetel wifi router (that was once used with airtel) for tikona connection. ๐ and indirect thanks to Rajat as well, who gave us enough info on MAC cloning.
Is TP-Link W8968 router support tikona net
all the adsl routers should have configuration to be used just in bridge mode!! please try to find out that in your configuration pages.
Dear Shain,
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKAU1159 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Dear Shain,
This is a gentle reminder to follow-up on your concern listed on Aug 19, 2013. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKAU1159 in the subject line.
Regards,
Tikona Care
Dear Shain,
Gentle reminder # 2
We have not received your information for us to take it forward. We now request you to share your detail on our official Tikona Forum – forum.tikona.in by mentioning the reference number in the subject line.
Regards,
Tikona Care
Thank u for posting its really working for me
welcome.. ๐
Hi Nitin,
I tried all the steps above , still its not working with my 450TC1. Can you mail me a screenshot of your configuration.
Thanks,
Naman
Hi Naman, there is no other configuration screenshot! All of them I have already attached!
Hi Nitin
i am trying to use UT STARCOM WA3002G4 BSNL adsl modem to use as wifi router
the wifi works fine when i insert a LAN cable coming out from another DSL modem in any of the LAN port
the wifi even works fine when i insert my office LAN cable where internet is available through a proxy address
But it does not works at my home where i am using a cable net from Intech Broadband. ISP has provided me internet using 2 pair cable though a RJ45 connector. he has provided me an dialer which i am supposed to dial after inserting LAN cable. in my case wifi connects dialer dials ocer wifi but after getting msg of “verifying username password” connection gets denied. also system shows IP conflict error when tried to connect/ after some time
ISP has mac control at their end of which i have taken care of
Amit Harer
9004030167
Thane Mumbai
Hi Amit,
try to resolve the IP conflict. was going through this website for your mentioned modem -> http://www.tricksguide.com/configure-bsnl-wa3002g4-broadband-adsl-modem-internet-lan-wi-fi.html . Disable the DHCP, IP conflict can happen because of that.
And try to find out, the IP series that you get, after connecting through LAN is same as that when you connect through WAN, or not?
hey ..
the input to the router is thru the lan from tikona to a lan port in beetel rite?
in wic port will v get the output to connect to the pc..
thank u
Dear Vikas,
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKSE1296 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
hey ..
i am getting the wifi signal but i am not able to access it as it shows your adsl is down .pls chevk the line ,,, pls help me access it ..pls
thank u ..
after which step and trying which step you are getting this error?
Hey Nitin….yours is the closet blog I can refer to…but still I am not able to fix it….Was wondering if you can guide me thru this….I have beetel 450 BXI ADSL2 router..so in this case i dont see the options which you are getting like the “Interface setup” I get only below options once i hit 192.168.1.1 under wireless tab
Basic
Security
MAC Filter
Advanced
station Info
Please suggest….I hate to use the LAN like everyone ๐ Thanks in advance…/ cheers
Just to add ..I am trying to configure it with Tikona
Dear Jagtar,
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKSE1449 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Hi Jagtar, try to find out configuration for setting up your router into bridge mode, and also for disabling dhcp. These two are the important steps. Else you can share screen shots of the configuration pages. will look at it to help you out if needed.
when i try to change the wireless mac filter to be activated then my tikona is not getting connecting in any laptop.. we have 4 laptops here…
hi nitin..
i have an airtel connection.They gave me an beetel 450tc1 ASDL2+ Router.
the problem is that i cant get the wifi signals in my room ( it shows the SSID but the signal is too weak to connect) . Is it possible to setup another beetel 450tc1 router as a repeater without using a LAN cable between them?
Hi Gaurav,
don’t think it will be possible.. still I ll give it a shot.. will try if any options available to make such a configuration possible.
Hi Nitin,
I am also having Beetel 450BXI ADSL2+Router but I have forgotten its password. I am not finding any reset button so that I can reset it to the default setting and can change the password. Going thru your blog, I also tried with the IP config command but its showing
Autoconfiguration IP Address: 169.254.207.252
Subnet Mask:255.255.0.0
Default Gateway: blank
Kindly help me plzzzzzzzz
hi nitin,
plzz help me.
I have tikona connection. Now i want to use it on my smartphone.
then what i need to buy a wifi router or adsl2+router.
which is better to buy for future purpose.
a frend of mine told me that tikona will not work on adsl2+router because tikon doesn’t need modem.
kindly clear the confusion.
Can i use purchase beetel 450 bxi adls2+ router.
Or i should but only wifi router.
Plzzzzzzzzzz
help
hi Aftab,
go for a wifi router,, as it will work!! This post helps out to reuse adsl2 router, in case ppl already have it. If going for new one then always better to buy a wifi router, as it can be used with any ISP.
Hey eNitin,
gr8 job bro..!!
just a prob.. my beetel 450tc1 admin & password options are not working. tired all ..
& also reseting nthng happening.!! pls suggest..!
Hi Vaibhav, there should not be any other password then what we all have tried with, i.e., admin/password. Hope if nothing wrong with the router, then resetting it will always work!!
Hi Nitin,
Thanks for the help. Your guide worked as mentioned. However 2 out of 4 LAN ports in my beetel modem are labeled as iptv and VoIP. The other 2 ports are labelled NET.
I use one NET port as LAN in and the other as LAN out.
However the iptv and VoIP ports somehow are not being recognized as lan out and don’t allow me to use for my other devices. I need to switch ethernet plugs manually each time I need to use a specific wired device.
Any suggestions. I got my modem from mtnl.
Cheers.
Hi Rajiv,
Sorry, no idea about it!
Hey Nitin,
Can there be some solution to 450BXi to be used as a “repeater” or in wireless bridge mode?
It can probally be used in wired bridge mode but I need A wireless setup or I will have to buy a new repeater or a router with repeater or bridge function which can be used as acess point.
This setup works like that only, just give it a LAN input. It will work as wifi access point or repeater you can say.
Hi, Can you please suggest what were the IP address assigned for the internet wire connected to LAN port and personal modem connected to Lan port ?? I suppose the latter will have private ip.. how did the router manage to do mapping or did you assign a gateway on your PC.. network connections… ? Can you please help me know the exact ip address (Except some octet of public ip) to understand how the setup works. Thanks for posting the details anyway.
Hi Nitin,
I am using BEAM connection. The wifi device provided by BEAM is not worth. low range and much ping time.. I have one old TIKONA wifi device. both the BEAM and TIKONA device have input of RJ-45 cable. I tried using the Tikona device in replacement of BEAM device. But am unable to use it.
Please can you help me with the same. When I replace the beam device with Tikona device, though my laptop can find the wifi connection. but am not able to connect to it. password is not matching for the device. i tried resetting the password by manual switch below the tikona device, but its still password protected. Tried reaching to the device via browser by 192.168.1.1 .. But still am not able to connect.
Please suggest what can be done.
Thanks in Advance
Rachit.
sorry Rachit, no idea about it! ๐ฆ
Dear Rachit,
Greetings from Tikona.
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKNV0236 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Dear Rachit,
This is a gentle reminder to follow-up on your concern listed on Nov 7, 2013. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKNV0236 in the subject line.
Regards,
Tikona Care
Can’t believe a company Tikona is tracking the comments and offering to provide service.. The best I’ve seen. However, I navigated to tikona tariff page.. The charges are too high than what my cable broadband asks for… I suppose I’m getting a connection of 10mbps for Rs 500 with unlimited usage.. Tikona gives around 8800… 9900 with tax for 1mbps. Although I don’t think practically speeds can range to 10mbps.. but it’d still be over 2mbps. I’ve called for a demo .. lets c.
Anyway, kudos for your service centers.
Hello Nitin,
I have beetel 450 TCL with airtel internet connection.I hard reset my modem and now iam not able to login to my modem control pannel using any of the default username password. I tried admin/admin,admin/password,admin/1234 .
Also my ssid has been changed to AIRTEL and Password changed to 0987654321 after reset ..Now i want to change my SSID and password by unable to do that as i can’t login to my modem. I have been trying to fix this from last two days but no luck ๐ฆ please help
@enitinkumar -Thanks a ton: those settings worked for me. I m using it with 24Online and tikona. it it is working for both. great jod dear.
Thanks Bro …
I Got iT……..
Sir, Are you trying to connect ADSL router to cable broadband ? In case that is the case, I’ve a beetel router and subscribing for cable broadband from local cable tv company. They said they will install a modem at my place that will connect to the tv set top box (digital) at one end.. and they will give me an ethernet connection to connect to my laptop. Can I just plug in that ethernet connection to my router, connect my laptop in wireless mode to router, set interface to bridge mode and browse internet ???
Some queries are:
do we have vpi vci settings in cable based broadband… ?
Will I have to disable DHCP ? And the IP for cable LAN will be assigned by cable operator.. for my machines I can configure a static IP for my devices.
Even with bridge mode connection , how would the router know which port is it supposed to forward the data to ? because I will not have any wire plugged into the Line port on the router.
I’m having beetel 450bxi adsl2 router+modem
Do Cable broadband connections have any of the following values port, vpi and vci ???
Hello Jay, the configurations that I have mentioned, converts adsl modem to a dumb router, just converts your lan to wifi. I don’t have idea about vpi and vci setting, never came across anything like that.
about anyone connecting to my router to get access to tikona network, they must know password to connect to my router, and for mac cloning my mac addresses, so we are safe here.. nothing to worry!
Tikona is good, but yes costly, and the bad thing is their call center ppl will keep you calling for the payment. So, choose wisely.
And if the router is configured properly, it will work with any ISP.
THanks for replying..
>>about anyone connecting to my router to get access to tikona network, they must know password to connect to my router, and for mac cloning my mac addresses, so we are safe here.. nothing to worry!
No.. no.. not about someone connecting to your router over wireless medium to get access to tikona.. that would be difficult. I’m talking about someone trying to connect to your router from tikona.. lets say I’ve been assigned IP 15.1.1.1 and you are at 15.1.1.2 both assgined by tikona. Will it not be possible for you to connect to my router, since my WAN connection is now connected to my LAN port, and go to router configuration page and modify the settings there ?
Also, I don’t see that option of Network Address in windows 7 for mac cloning. Further, is my understanding correct in: the mac address from any one of the device connected to the router over wire/wireless should be assigned to all devices connected to the router.. ?
Can we not configure NAT in ADSL router to achieve direct access ?
Thanks,
One more question dude, don’t you think this setting will give anyone in tikona network access to your router.. 192.168.1.1 as they are directly connected to your LAN port now ?? And if they use mac cloning.. how do you secure your router ?
i had configured the modem earlier and it was working fine .. but suddenly today it stopped working .. i access it thru my mobile .. the mobile keeps showing “obtainin ip address”.. when i tried to configure the modem again i cannot connect it to the system only .. and the modem is not resetting .. pls help me thank u ๐
“obtaining ip address” error for me used to come, whenever tikona service wasn’t working. But, resetting also not working.. then, no idea. might be your hardware is gone.. ๐ฆ
Thanks for the help @enitinkumar..
i configured it and now my wlan modem is working like a charm… thanks to you.. you save my 2k.. as i was about to buy a new router for tikona but thankfully you saved my savings..
just have one query.. are you able to access internet access on the rest of the 3 ethernet ports…??
as my router is working fine with wifi… as my tikona plan allow 2 users at a time..
out of the 4 ports.. 1 port is occupied my tikona..
nd rest 3 r free.. but m not able to access internet through it…
plz help me out regarding this… thanks in advance ๐
most welcome.. ๐ feels great that my post is so much of use to everyone !! ๐
regarding usage of ports, yes you can, but the number of internet connected systems, that depends on the plan which you have taken, for me it is 2.
Dear Subscriber,
Greetings from Tikona.
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKDC0457 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Dear Subscriber,
This is a gentle reminder to follow-up on your concern listed on Dec 8, 2013. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKDC0457 in the subject line.
Regards,
Tikona Care
Dear Subscriber,
Gentle reminder # 2
We have not received your information for us to take it forward. We now request you to share your detail on our official Tikona Forum – forum.tikona.in by mentioning the reference number in the subject line.
Regards,
Tikona Care
Hi enitinkumar,
Can I use I-Ball 150M Wireless-N ADSL2 router to connect to pioneer/ beam and enable wifi.
Thanks,
Raghav
Hi Raghav, haven’t seen configuration for this modem ever. Just try to find out if you can disable dhcp and convert it into bridge mode or not.
Hi Nitin,
Need your help. I have Beetel 450TC2 modem + Wi-Fi router and Airtel Connection. The Wi-Fi was configured by the Airtel representative. I am facing an unusual problem. The Wi-Fi once configured is detected in all devices at home i.e. 2 personal laptops and 4 mobile phones. But once the modem is switched off, the laptops are not able to detect the Wi-Fi network. I brought my office laptop to check the problem. The office laptop detected the Wi-Fi network every time after switching off the Modem. One of the personal laptops have the windows 7 and the other laptop is a brand new laptop from HP with Windows 8. Please suggest what should I do
hi Pradeep, sorry couldn’t understand your problem. I guess you want to say, is once restarted, your devices are not able to find the wifi-network. If it is, it’s quiet weird. I haven’t seen any configuration to make router’s ssid hidden. So, sorry I don’t have idea about this problem. ๐ฆ
Hi nitin,
I just got a tp link wr543g installed. a private company installed it on my roof. A lan wire is connected to my laptop from that router.internet works fine with this. Now I want to connect multiple devices with it via wifi.i have an extra beetel adsl modem + router. Please tell me how to connect these and how to configure my beetel router so that I can connect my devices over wifi.. Please helppppp!!!!!!
Hi Ravi, just try out the same settings that I have done. Connect the lan cable from the router provided by the ISP to your router, after configuring.
Hi Nitin,
I have an adsl beetel router 450 tc1.
I followed the same steps to configure it for Tikona but it didn’t work. After all setting and restarting it, when i try to connect from laptop, it is giving me error – uanble to connect.
Can you please help me here.
Kindly let me know ur email so that i can email you the snapshots from my end and you can guide me on this.
Hi Manoj,
you can add me on skype.. “enitink”
DSL flashes in between for me too.
Dear Manoj,
This is a gentle reminder to follow-up on your concern listed on Dec 21, 2013. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKDC1282 in the subject line.
Regards,
Tikona Care
Dear Manoj,
Greetings from Tikona.
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKDC1282 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Also want to add that I am inserting the LAN cable from Tikona to the LAN1 port and then DSL flashes in between regularly. I have followed only steps 1 to 4. Once it will work, will check for MAC and rest. Thanks in advance for your help.
Where do you provide the IP address and gateway details provided by the ISP?
not required in my case, just modified my router to be a dumb one, dependent on info provided by isp router that it is connected with.
ok, that means you just got the username and password from your ISP? You didn’t get any ip address or gateway details?
No, details I was just given for tikona portal, where I had to login, to access internet.
ok, so how do you get an ip address 1.xx.xx.xx? Have you set the option “obtain IP addreess automatically” or have done some other settings?
this is what disabling the dhcp for adsl router does. IP address is assinged automatically. Try out the settings mentioned. and observe if it’s not as per requirements!
i am using binatone dm856w router provided by mtnl broadband and tikona bradband connection.
i have made the necessary changes you have provided in my router and also successfully using my tikona broadband in my 2 android devices.
but the problem is i am unable to coonect on my laptop.
please help i have tried repeating all steps again but nothing worked.
i can connect to wifi but not able to open even the login page.
can you check, what is the IP getting assigned to you in your laptop ?? if it’s not similar as what is assigned to you in your android devices, then check by mistake static IP is configured in your laptop.
Dear Muneeb,
Greetings from Tikona.
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKFB0027 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Is there any possibilities connecting beam fiber with beetel 450tc2
it should be, these configurations converts 450tc2 into a dump wifi access point. so it should work.
Thanks Nitin for quick reply.
Let me tell you what i have done so far…
Reset the router
Changed setting in router
Beam broadband connection to router lan1 port.
Ethernet cable into lan2 port of router & that goes into laptop.
But nothing worked.
After sometime if i try to connect broadband directly to my lappy …no internet connection.
Port blocked.
I have to wait for few hours to get back to network.
Can you please tell me what exactly need to change in router and laptop settings.
Anil, I have never seen how beam connection works. So, won’t be able to guess what to try out.
These settings have worked with tikona, ACT, lan network.
You need to check with beam, if you want to add your router what should you do.
nice information for Belkin router…
belkin router setup
Hi enitinkumar
I have a query for extending my wifi range using a 450TC1 as repeater. kindly help me with the same.
I use hathway broadband wifi Connection they provided Dlink DIR 300 For wifi connectivity
i wanted to know if i could use my spare 450TC1 to extend the range of mt network wirelessly would be great. Please steps as i’m no expert. ๐
Thanks in advance
Regrads
Lohit Rishi
Hi Lohit.. I don’t think we can do it wirelessly, a lan wire is required to be pulled from your hathway router into beetel router. Other than that.. i don’t think any possible way is there.
Many Many Thanks for such a wonderful knowledge sharing Nitin !
Hi,
I have netgear dgn1000 DSL router, cam I use it with Tokina bb services.
sorry, no idea.. ๐ฆ
Dear Saurabh,
Greetings from Tikona.
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKMR0976 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Dear Saurabh,
This is a gentle reminder to follow-up on your concern listed on Mar 18, 2014. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKMR0976 in the subject line.
Regards,
Tikona Care
Hi enitinkumar,
i am using Beetel 450 TC1 router with tikona.
Please may i know what fields need to set in wireless tab.
Regards,
Ram
I mean in SSID column, key#1 column (is it password?) & in mac address.
regards,
Ram
Hi,
SSID – name for you wireless connection.
Key#1 – you are correct, it’s password.
MacAddress filter – is extra support for safety, you can put your devices mac address here. To get mac address of device like phone check in network connection. for windows you can check on cmd using ip \all and put wireless adapter mac address, in linux it’s ifconfig.
Dear Ram
Greetings from Tikona.
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKMR1085 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Dear Ram,
This is a gentle reminder to follow-up on your concern listed on Mar 19, 2014. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKMR1085 in the subject line.
Regards,
Tikona Care
Dear Ram,
Gentle reminder # 2
We have not received your information for us to take it forward. We now request you to share your detail on our official Tikona Forum – forum.tikona.in by mentioning the reference number in the subject line.
Regards,
Tikona Care
Hi Enitinkumar,
I had one more doubt on connecting cable to router.
First i connected the cable coming from modem to router in LAN1 port.Then with another cable i connected LAN2 to laptop,with this i able configure the router.After this, no need to connect the cable to laptop, right ?
Regards,
Ram
i have beetel router and have spidigo conection but i am not able to configure it as because i dont know how to i was having airtel connection it was connected with my router do we have to take out ethernet cable of spidigo and place it to our router and then start configuring or before how to
please help me
before putting spidigo cable, try configuring.. after configuration is done.. put spidigo cable and then restart.
Hi, Recently I bought Dlink DSL-2750U modem+router for home use. I want to configure this router but router WAN port accepts RJ11 cable. And tikona has RJ45 cable.i have bridged the router but my wifi always stucks on getting ip address….
are you able to connect to your router, by just removing tikona connection?? ,, and make sure you disable dhcp of your router.
can i use asdl Beetel450tc2 to connect ACT BB which is fiber optic cable connection.
give it a shot.. ๐
hey hi,
I’ve been trying your method with wimax provided by bsnl and beetel ADSL2+router but it didnt worked can you please assist me…
Thank You.
where are you getting stuck??
are you able to connect to wifi ??? what is the ip that you get.. is it of same series as what you get when you directly connect to the cable provided by bsnl wimax?
Hi,
I have a problem related to beetel ADSL2+router. When I tried to configure my BSNL broadband I found out that It is by default configured for Airtel broadband & wifi settings. I then Reset it to default settings but nothing changed. I am not able to change settings for wifi either. I want to know how can I delete Airtel settings from the modem? If required I can also send the screenshots of setting pages.
Yes, it’s by default configured for airtel broadband.. I didn’t get any chance to try out my modem with anyother dsl service provider.. so sorry no idea about it.. ๐ฆ
Hi Nitin,
Using the above guide I was able to configure my TP-Link router with Hathway (where a dialer is created with id and password on the PC).
My questions are :
1) I am unable to connect my wifi devices such as phone as the router does not send the traffic to Lan Port 1 from wifi devices. This is not a problem with my PC. How to I set up a wifi route to connect wifi devices. Hathway has provided me a dynamic IP via DHCP.
2) How do I connect to internet directly from the router without dial-up from the PC?
Thanks and Regards,
Hi Rohit,
regarding 1 – I am not able to understand what is the problem.. ” router does not send the traffic to Lan Port 1 from wifi devices.”
regarding 2 – I don’t think it will be possible. as it’s airtel which would have put there firmware for the router.
thanks for sharing this information.
keyowrd
welcome.. ๐
Hi ,
Lots of thanks Nitin. Just now I was able to successfully configure my Beam telecom connection on Beetel 450 TC2 modem.
Only one device gets connected at present as Beam requires a portal login. But that solves 50% of my problems.
Mostly following steps 1 to 4 of what you stated is enough to configure the Wifi distribution of Beam connection on one of the LAN ports.
But I had a router that had some other connection issues in regards to Wi-fi connection. I couldn’t modify “Authentication type” for the Wi-fi connection ( default set to WEP ). Most of my android devices failed to connect with this authentication.
Hoping that these instructions might help someone else in need –
before following the 4 steps mentioned here, I had to follow what has been mentioned on following page in Comment#16 by yuga —
http://broadbandforum.co/topic/53726-beetel-450tc1-firmware-update/page-2
The link also has a step-by-step instruction to apply the firmware upgrade ( in my case , I think it was a downgrade in version , neverthless it worked ) .
Note1 : at 100% of applying the firmware upgrade , the device might not automatically restart as is mentioned in Step 3. Wait for 5 mins. and proceed with Step 4 of the readme.
Note2 : Default admin password for accessing http://192.168.1.1 was password, but after applying the firmware update that yoga points to in that link, the password changes to admin.
Nitin, one more point. I am not able to access the http://192.168.1.1 link of the router’s configuration after following the Steps 1 to 4. Not that I need it or am bothered about it, but if that link can be accessed, please let me know.
Finally , regarding Rajat’s comment about applying MAC cloning. Correct me if wrong, but the android phones can’t use MAC cloning , so how are you using multiple phones to connect ?
Hi Keshav, thanks for sharing your findings.. ๐
Regarding 192.168.1.1 not accessible, yes it won’t be as we have disabled dhcp. Just try it after removing isp lan cable.
MAC cloning, is not possible in latest versions of windows too.. I guess it’s for xp and windows. Never did RnD regarding this, as I was having only two device.. ๐
Hi Nitin,
I use to have an MTNL connection with ADSL modem. Now switched to spacenet (local cable service provider). They have created a pppoa / pppoe dail-up on my desktop. MTNL also use always on pppoa / pppoe connection. Is there a way I can user LAN port to dail to spacenet from my 450tc1 as I have input from a CAT5 cable?
Regards,
Manish.
Hi
Can You help me with the settings for blocking an IP or MAC on a beetle 450tc2 router for airtel connection.
I tried a lot but it doesnt seems to be working
Can you give the setting values that needs to be put or what to be put in which coloumn
Hi Sami, I don’t think blocking is possible.. only known you can add, if you don’t want any mac to get connected to your router, just remove it from configuration.
I have Huawei wa1003a wireless modem. Can I use it with tikona wimax?
thanks!
try searching in configuration, if it is possible to enable bridge mode, and disable to dhcp.. if yes, then you can use it.. ๐
Hi Nitin,
I went through your profile and was convinced that you would be able to solve my problem. Actually, I am trying to share the internet connection from a USB Modem (Tata Photon+) to other devices using the Beetel 450TC1 router which was provided by Airtel. As of now, I am not using the Airtel connection. I have a laptop with WiFi adapter, a Tata Photon USB Data Card, a wireless router( Beetel 450TC1), a LAN cable and a few portable WiFi enabled devices. Given these items, can you please help me with the steps for accomplishing this? In other words, I want to first connect to internet through Tata Photon dongle in my laptop. And then I want to relay that internet connection to the wifi router and then I want to access the internet through the wifi router on my Mobile devices, like Mobile phone, tablet and other laptops. Hope you have understood my problem/ requirement. Any help would be highly appreciated.
Thanks
Abhishek
Hi Abhishek, thanks for encouraging words.. ๐ .. but I think you can directly achieve wifi sharing, using wifi hotspot/adhoc network of your laptop. Using airtel router in between will not be possible. Or else you can try out this router. You can plug in your dongle and enjoy wifi over other devices, no need to switch on the laptop.
Hey Nitin,
I also have a similar Binatone ADSL2+ Router (DT840W Model) which I have recently configured for a Tikona Connection. Everything is setup properly and everything works fine, except for the fact that it has a Session Limit of only 2 (only 2 devices can use the wifi at a given moment, which is very sad). I want to increase this to about 4-5 max, but am having difficulty doing so via the Binatone Router Setup page (available on 192.168.1.1). I read up that we can increase the session limits preferentially, so need your help for this.
Thanks in advance!!
Hi Ranabir, I have by myself never tried it. Please check comment of Rajat, about mac cloning.. try it out! hope it works.
Dear Ranabir,
Greetings from Tikona.
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKJU0252 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Dear Ranabir,
This is a gentle reminder to follow-up on your concern listed on May 31, 2014. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKJU0252 in the subject line.
Regards,
Tikona Care
Dear Ranabir,
Gentle reminder # 2
We have not received your information for us to take it forward. We now request you to share your detail on our official Tikona Forum – forum.tikona.in by mentioning the reference number in the subject line.
Regards,
Tikona Care
Hey Guys I tried the steps and it worked .. But the its only working on LAN for 1 computer .. my other computer is connected trough wifi and it always says no internet access
Pleas Help ?
Same Router and Tikona Connection
Gaurav, check what is the ip assigned when you connect to lan and wifi, if not of same kind then check your wifi adapter configuration. And you have to sign in to tikona network from all the systems connected.
Dear Gaurav,
Gentle reminder # 2
We have not received your information for us to take it forward. We now request you to share your detail on our official Tikona Forum – forum.tikona.in by mentioning the reference number in the subject line.
Regards,
Tikona Care
Dear Gaurav,
Greetings from Tikona.
In order to assist you, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKJU0251 to your case. Request you to write to us on tikonacare@tikona.in. with your details and mention the reference number in the subject line.
Regards,
Tikona Care
Dear Gaurav,
This is a gentle reminder to follow-up on your concern listed on June 3, 2014. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKJU0251 in the subject line.
Regards,
Tikona Care
Can you mention 1 more thing, how did you connect to wiring and where do we enter the broadband user / password for dial up ? Thanks
Also, what is the model number of beetel modem you have ? and the version of firmware ? I’m getting many options under bridged mode like VC or LLP etc.
Hi I had followed your steps and successfully configured my rp link modem to work with tikona. However since 2 days I am unable to connect to internet through the modem as ip address is not getting assigned. Any pointers pls?
Hmm.. not sure about this, I faced this problem only when tikona network was down.
Dear Divya,
Greetings from Tikona.
We have noted your post. In order to assist you further, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKJU0522 to your case. Requesting you to mention the reference number in the subject line while sharing your details with us on tikonacare@tikona.in
Regards,
Tikona Care
Solved successfully! I reset the router and updated the firmware. Also changed d lan ports for good measure. Now working somehow.
Dear Divya,
This is a gentle reminder to follow-up on your concern listed on June 8, 2014. Requesting you to share details in order for us to assist/resolve your concern. Kindly share your details with us on tikonacare@tikona.in mentioning your assigned reference number TIKJU0522 in the subject line.
Regards,
Tikona Care
Dear Divya,
Gentle reminder # 2
We have not received your information for us to take it forward. We now request you to share your detail on our official Tikona Forum – forum.tikona.in by mentioning the reference number in the subject line.
Regards,
Tikona Care
Wow! it works .. after denied by local ISP for its functionality i was forced to buy a new router… but instead i tried to take a shot and now yeah !! Thanks a lot ๐
Where can we see the logs in beetel router 450tc2.
In my previous router, I had an option wherein i can mail all the logs, username and password on email address. Where can i find this option in the router login page
No idea, never seen anything like that.. and I dn’t have the modem with me now.
Hi,configured the same for beam. But the problem is I’m not able to connect multiple devices at a time. It’s allowing only one device to connect. Will it be solved is I enable DHCP?
If i enabled dhcp, then login page for tikona never used to come. Not sure about beam.
I’ve successfully configured wifi with the steps that you provided. But i a desktop which i need to connect over LAN. What steps should i take in order to have it route over borth wifi and LAN?
just connect any lan port with your desktop, it should work.
Will this work for more then 6 session? Or it has session limit like?
Please help.
Thanks for your hard work and good deed.
regards
sagar
sorry, couldn’t understand your requirement. What session you are talking about?
As per router goes, I never checked, if It has any max number for connected devices.
I have a beetel 450tc2 modem that was given when taking airtel connection in hyd
Now I m leaving hyd and want to sell it off .Will it work for other connections or only airtel connection ?
While installing I asked the person who came to install ,he told there is no lock .You can use for any connection .But I have seen him updating firmware from some airtel link .Will that cause a problem ?
I don’t think that should be any problem. Anyways try if doesn’t work, then sell it.. ๐
Hey Nitin…. Thanks for sharing this information.
Unfortunately I didn’t see this article on time and ultimately bought D-Link Modem to comply with Tikona connection. Now my Airtel Modem is lying ideal for nothing.
Just a question… can i somehow also use my ADSL modem in conjunction of my present D-Link modem? Something like using both the modems. I don’t know much about these modems so this may sound a weird idea :)…. The only purpose which I wanted to achieve is to increase the WiFi coverage area by adding ADSL modem. Is this possible or I really am a dumbo? ๐
Yes Tarun, I think it is possible. just pull out a lan cable from your D-Link modem and put it into your airtel modem.
buddy i need help it followed all steps , added my mac to mac addresses and then it did work but on lappy it opens a page and ok tikona login saying maximum devises something unable to logoin what to do , i gess im too late or are you still active here ??please respond, i hav been trying to do it since yesterday
sorry for late reply, saturday/sunday kind of no internet day for me.. ๐
Anyways.. I had two devices allowed for my tikona network. So after connecting two devices to internet, on 3rd one I used to get “max number of devices reached”, for this check with tikona guys on max number of allowed devices to connect to internet for your plan. And one more problem with tikona is it has limit on no of devices ever connected, for this problem you need to reset devices info on tikona portal, never done that but I know that something like that is there.
Nitin kumar waiting for your response. Please revert soon,
I have configured now . but at this point this. If I connect my HTC m7 and Samsung laptop ,it connects to WiFi but, when I sign in to tikona login. It only works in one device ..other say authentication failed ,failed simultaneous sessions something. S what to do to make it work.? Please help.
Sunesh.kumar@me.com
Dear Sunesh,
Greetings from Tikona.
We have noted your post. In order to assist you further, we would require your contact or Tikona User ID details. We have assigned a reference number # TIKSE0048 to your case. Requesting you to mention the reference number in the subject line while sharing your details with us on tikonacare@tikona.in
Regards,
Tikona Care
Tikona care … Please … Don’t trouble me anymore already and do not inter fare ,had so many issues with u ,I am at a point of not paying your bills anymore… Please check the complaints since June. You people sitting in call centre are bunch of liars…seriously ,please the person who sent this message don’t take it personally.
Reblogged this on Suneshbenny's Blog.
That’s the same error I’m getting maximum devices .and confirmed with tikona .only 2,are allowed at a time.so what should I do as I have to connect smart phones and a laptop ..can you please throw some light on it.and thanks for taking out some time for us.
i have HAME MPR-A1 3G WIFI router and Airtel broadband with BEETEL 220BXI ADSL2+ MODEM. How to make connections so that it works as a wifi for lappy, phone etc and simultaneously work internet on the PC through network card?
looking at this page .. feel like you can just put lan cable from your airtel modem into rj45 port and start enjoying the wifi.. as it says no config required.. should not be tough to to
Excelent work Nitin!! Your post was excellent.
The method suggested by rajat may not work with multiple devices. The basic is, a request can be sent but the router will not know how to send back the replay as there willl b same MAC id ill be assigned to multiple devices. My linux laptop configured as NAT solves my problem ie ethernet port will be connected to tikona, my laps wify interface ip will be gateway for other devices. I’m sure there must be some way to do this in wondows as well
Hi,
I have a service provider who provided me dial up connection. i.e. a lan cable comes to my pc and then connection is established. Is there any way so that I can share this dial up connection over multiple devices? I have beetel 450TC1 (adsl2+ router ) modem.
Thanks
Nipun
Hey tried it for more than 10 times, not working, you are using LAN connection or wifi?
I don’t know, are you using any kind of adapter between the output and input.
I connect LAN cable with RJ45 directly into the LAN port of adsl2+router and following the procedure as you told. No propitious results are found. I want to connect my iPad, by the way is it possible if I follow the procedures directly using iPad? And I also get connected to the wifi network on my iPad but with no internet access.
what exact problem you are facing? After which step, if you can tell me more elaborately I might be able to be of some help.
Exact problem is that I cannot connect via wifi, even when I followed the procedure, with the Adsl+wifi router
dear nitin kumar i have beetel adsl2+wifi router at the same time i have local broad ban cable which is small port than beetel how can i connect
how do you connect it to your laptop?
I have followed your steps..
Done some research and i am successfully using my net on laptop through 450tc1 router on my PC through Ethernet or WiFi.
But My problem is
1)the ip given by tikona starts with 10.25.xx.xx ,something like that and router ip with 192.xx,so i cannot configure my router when i am connected with internet,so i have to unplug the tikona wire from router and so then i can access router page.
2)And many times i don’t get access on other devices(mobiles),it connects to router but it shows (no response to internet on my WiFi) and no login page of tikona comes,and sometimes it connects,means 1 out of 3 times i can connect my WiFi. first i had put mac address of my phone so it connected and again it is not connected so now i have removed mac address filter.
So what should i do???
Hai Nitin ,
I am having beetel 450TC2 ADSL2+WiFi router with Airtel connection.I am not able to connect my iPhone when some other device is connected to my WIFI,once the other device is disconnected then only my iPhone gets connected this issue happens only to this Router.Pls tell to configure to fix this issue
Hi Nitin
I have a wifi Beetel 450BXi modem by which i am running 2 laptops & 4 pc’s, now i want to allow access to only two sites on rest of machines & full access on only my machine, is it possible & how come, waiting for a positive reply, thanks in advance.
I have a UTStarcom ADSL2+ modem router can i use just ethernet part of it so that i can connect 3 more systems
hi nitin,
i have beetel 450tc2 modem and a tikona connection with static IP.
I have found this blog which is exactly what i am trying to do.
I followed your steps however i am not even able to connect to the wifi
Below are the steps that i performed.. please let me know if i missed sth
– Connected modem with laptop
– changed the configuration as u mentioned
– added MAC address also to the MAC filter
– rebooted modem
– wifi on > tried connecting to the wifi and received error message “could not connect to this network”
please let me know if i need to do sth else too….
I would be grateful to you.
thanks in advance.
Dear Nitin Kumar.
You are really amazing.this post helps me a lot.thanks for the post.
I tried to connect the beetel 450TC2 to hathway internet. perfomed the same steps as per your post. I am able to connect through lan.like hathway lan(RJ45) -> beetel LAN1 -> another cable,RJ45,Beetel LAN2 port -> My laptop LAN.
its working perfectly.But I want to connect through WiFi. I can see my WiFi name in the list and I can connect to it. sometimes its connecting and sometimes its not.But if I remove the Lan,not able to connect to Internet.I have updated the mac address in the interface setup(WAN).
Please help me.
Also internet light is not blinking on Beetel wifi router.
Pingback: How To Figure Out Ur Router Password | Information